FLOXPRESS TUTORIAL PDF
This tutorial is intended to give basic instruction on how to setup and run a Note: FloXpress will not work if the Flow Simulation add-in is currently installed. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. Based on the results of the. This simple tutorial is designed to show you the process of solidworks floxpress. The part that we use here is a simple part because our main goal is the process.
|Published (Last):||6 February 2016|
|PDF File Size:||18.73 Mb|
|ePub File Size:||15.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
A sample floxpgess is like the one shown below. The first step is to ensure that the model has no openings fully closed with lids.
From the flocpress we can obtain properties such as maximum flow velocity. The check geometry window appears which indicates the smallest passage. This free tool allows you to calculate how fluid or air flows through a part or assembly document.
Once we have created the lids we can then proceed to begin the simulation. Use this information in conjunction with experimental data and practical experience. We need to first create the lids for the two ends before we begin the simulation.
Home Support Daily Dose The FloXpress wizard has a procedural sequence that enables the user maneuver through the simulation with ease and comprehensively understand the simulation. First you must model the following part and I assume that you know the basics of solidworks 3d modeling.
Contact us for more information and buying SolidWorks at support nccs. The part that we use here is a simple part because our main goal is the process of floxpress. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. This simple tutorial is designed to show you the process of solidworks floxpress. We are here to close the two ends of the part so insert a new part just like below:. Excellent help tutorials with your Free Xpress Utilities series.
This simulations can be done using either pipes or bubbles. The velocity chart illustrates the flow speed during the processthe colors are observable in the flow.
SOLIDWORKS Free Xpress Utilities-Part 4-FloXpress
This is a great tool to help you identify problem areas in your tutoria, and improve them before you manufacture any parts. You cannot use different fluids simultaneously. You can examine the flow in much more complicated parts like valves too the process is the same.
The Solidworks FloXpress icon is located under the evaluate tab.
SOLIDWORKS FloXpress is fluid flow simulation add-in software
Once the geometry is valid, you next flospress water or air as the fluid for the calculation. A Microsoft Word report can be generated. Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks loft-1 solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing Field testing is mandatory to validate your final design.
All of these articles will be stored in the category of Daily Dose…. Define a plane parallel to the end floxpgess of the part and set the mm offset distance. SWA home about contact us. Now the part1 is added to design tree. A new assembly opens, the begin gloxpress window appears with your part ready to insert, just click on the working area and your part will insert there. Home solidworks tutorial ebooks solidworks flowxpress Now the part is ready.
The inlet conditions can be defined in terms of pressure, volume flow rate or mass flow rate.
So right click on main part and select appearance. We then define the outlet conditions in terms of atmospheric pressure. Trajectories are tangent to the flow velocity at every point. Once a pressure is selected, you can run the analysis to calculate flow velocity. This was a very simple flow analysis. You can also choose to generate a report from the FloXpress simulation by simply clicking on the generate report icon at the bottom of the results tab.
I did it too, now or part is a closed flkxpress. For the sake of keeping this ttuorial short I leave it to you.
Tutorial – Using FloXpress in Solidworks? | GrabCAD Questions
The analysis is based on the calculated velocity field. I went with a C-D Nozzle geometry for this demonstration. Right click on it and select edit part:. From the results window you can simulate the trajectory of fluid particles as they move through the model. Now go for the floxpress on the tools menu again.
Close the check geometry window. Click next and then click solve and wait. The opening must be closed with lids.
The next step is to solve the model. Share this with your friends. Next we choose the fluid that would flow through the model. In order to see the lids and getting a better sight of flow later on, we need to transparent the part.